EKOPEL 2K-GOLD Bathtub Coating – Premium Complete Kit for DIY Enthusiasts

The premium solution for your bathtub resurfacing – no removal, no compromises. EKOPEL 2K-GOLD delivers a smooth, high-gloss surface that looks like new and is ready to use again in approximately 24–36 hours. The advanced premium formula with UV and HALS protection is specially designed for the highest demands – perfect for bathrooms with natural light or windows. Thick-layer, self-levelling 2K coating based on a high-quality epoxy resin system, including a complete DIY kit.

Premium formula with UV protection
Bathtub ready to use again after approx. 24–36 hours
Odourless & VOC close to zero
Thick-layer 2K coating
High-quality epoxy resin system
Smooth, high-gloss finish
High film thickness: up to approx. 0.5 mm on walls and up to approx. 5 mm on the base
Free from harmful solvents & mutagenic substances

€156,51 EUR

Taxes included. Shipping calculated at checkout.

1 complete kit = enough for 1 standard bathtub up to 170 cm in length.

Included in the delivery:

• EKOPEL 2K Gold coating (Component A + Hardener)
• Surface cleaner for preparing the surface
• Sandpaper for preparing the bathtub
• Wooden stirring stick for mixing the components
• Notched spatula for spreading the material on the tub floor

Technical specifications:

• Total volume: 2.4 L (1.9 L resin + 0.5 L hardener)
• Coverage: sufficient for 1 standard bathtub up to 170 cm in length
• Working time: approx. 60 minutes
• Ready for use after: approx. 24 hours

Additionally required or helpful (not included in the kit):

• 1 disposable plastic cup 500 ml
• 1 disposable plastic cup 200 ml
• Masking tape for taping off edges
• Protective foil for floor and bathtub front
• Garbage bags
• Paper towels
• Screwdriver for removing the siphon cover
• Utility knife for removing old silicone joints
• Baking soda for cleaning
• Hair dryer to warm the surface if needed
• Protective gloves
• Protective clothing or clothes that can get dirty

EKOPEL 2K Gold is applied using a pouring technique and self-levels on the surface. This creates a smooth, high-gloss finish without brush or roller marks.

Technical advantages:

• Suitable for bathtubs up to 170 cm in length and 80 cm in width
• Working time: approx. 60 minutes after mixing
• Bathtub usable again after approx. 24 hours
• Cleaning agents should only be used after approx. 7 days

Suitable for:

• Cast iron bathtubs
• Steel bathtubs
• Fibreglass/acrylic bathtubs

Key to a great result:

• Minimum temperature: +20 °C
• Ideal room temperature: +23–24 °C
• Heat bathroom 1 day before and 2 days after resurfacing

Shipping:

• Orders are processed within 1 business day
• Delivery time: approx. 1–7 business days, depending on the destination country
• Secure packaging designed for sensitive 2K materials
• Tracking available immediately after dispatch
• Delivery within Germany, to other EU countries, as well as the UK, Norway, and Switzerland
• For shipments to other countries, please contact us before placing your order

Important Information:

• Please check your items immediately upon receipt for completeness and any possible transport damage.
• Store the materials in a dry place at room temperature.

Returns:

• Returns of unopened products are accepted within 14 days
• Sets that have been opened or used cannot be returned due to the chemical nature of 2K products

If you have any questions, our support team is happy to assist you.

Technical Data Sheet (PDF) → View PDF

Safety Data Sheet (SDS) → Available on request

Quick guide (PDF) → View PDF

Detailed Instructions (PDF) → View PDF

Care Instructions for Your Bathtub (PDF) → View PDF

MADE IN EU

Made in Slovenia

Tested according to DIN EN 71-3

Free from heavy metals

Thick-layer coating

Up to 0.5 mm on the walls and up to 5 mm on the floor

Excellent Adhesion

No peeling when applied correctly

Personal Support

We’re here to assist with any application questions

How the EKOPEL Pouring Technique Works

See how you can resurface your bathtub in just a few hours using EKOPEL 2K Classic, Optimum, or Gold with the proven pouring technique.

The detailed process is demonstrated in the video. Please follow this link.

Frequently Asked Questions

All EKOPEL 2K materials are specially formulated for resurfacing old bathtubs and are applied using a pouring technique. They create a smooth, thick, and durable surface with excellent adhesion.

EKOPEL 2K Classic cures in approximately 48 hours and is especially well-suited for DIY enthusiasts due to its longer working time.

EKOPEL 2K Optimum cures within about 24 hours and is ideal when the bathtub needs to be back in use sooner.

EKOPEL 2K Gold also cures in around 24 hours and provides enhanced UV protection. If your bathroom has a window or the bathtub is exposed to sunlight, we recommend EKOPEL 2K Gold.

EKOPEL 2K is applied using a casting process. The material flows evenly over the surface, creating a particularly thick, smooth, and glossy coating.

EKOPEL Roll-On is applied in two coats using a roller. It is especially suitable when the drain cannot be removed or when a simpler application with a roller is preferred. Roll-On can also be used on wall and floor tiles.

EKOPEL 2K is suitable for steel, cast iron, ceramic, fiberglass, and previously coated bathtubs.

For acrylic bathtubs, use is only recommended if the walls are stable and not flexible. If the surface moves or gives under pressure, we do not recommend applying the coating.

For a standard bathtub up to 170 × 80 cm, you will need an EKOPEL 2K set with 2.4 L.

For larger bathtubs, we recommend an additional 1.2 L set.

For shower trays up to 90 × 90 cm, a 1.2 L set is usually sufficient. For larger shower areas, we recommend a 2.4 L set.

The EKOPEL 2K set already includes the base material and essential accessories.

Additionally, you will need masking tape, protective film or paper for the floor, a hairdryer or heat gun, a cup with a capacity of about 400-500 ml, tools for removing or opening the drain, a knife or cutter, cleaning cloths, and a solvent for cleaning tools.

We also recommend wearing clothing that can get dirty.

Before application, the bathroom should be thoroughly cleaned. Remove dust from shelves, walls, ceiling, and surfaces to prevent any particles from contaminating the new coating.

Take out towels, toiletries, and any loose items from the bathroom. Windows should remain closed during the process to keep dust and insects off the surface.

The room temperature should be at least +20 °C starting one day before application and maintained throughout the curing period.

The bathtub must be clean, dry, free of grease, and free from silicone, limescale, rust, and loose old coatings.

All silicone residues must be completely removed, as the material will not reliably adhere to them. Limescale deposits, rust spots, and loose old coatings must also be removed.

Deep damage, grooves, or chipped areas over 1 mm should be filled with epoxy or polyester filler before coating and then sanded smooth.

Pour the entire Component B into the bucket with Component A. Thoroughly mix the material using the supplied wooden stirrer.

Stir vigorously for about 10 minutes to ensure there are no unmixed residues on the bottom or sides. Then let the mixture rest for approximately 5 minutes before stirring again for another 5 minutes.

The material is now ready to be applied.

EKOPEL 2K is not applied with a roller or brush, but poured.

Use a cup with a capacity of around 400-500 ml and pour the product evenly onto the edges and walls of the bathtub. The material flows slowly downward, spreading across the surface.

This pouring method creates an exceptionally smooth, thick, and glossy coating.

If possible, we recommend removing the drain or at least covering the drain opening. This allows excess material to drain away cleanly.

If the drain cannot be removed, the drain opening must be carefully sealed. Cover the opening with paper, secure it firmly with masking tape, and carefully cut the tape along the contour.

The overflow should also be removed or carefully masked off.

The room temperature should be at least +20°C. This temperature should be maintained one day before application, during processing, and throughout curing.

For easier handling, we recommend warming Component A to approximately +30°C before use. To do this, place the bucket in warm water or store it in a warm location the day before.

Temperatures that are too low can impair flow behaviour and significantly extend curing time.

At a room temperature of approximately +24 °C, the bathtub can be used again cautiously after about 24 to 48 hours, depending on the product. At around +21 °C, we recommend waiting 2-3 days before using the bathtub. At lower temperatures, curing may take longer. Bottles, soap containers, pets, and products containing dyes such as hair colour or coloured bath additives should only be introduced after approximately 7-14 days.

Small dust particles, insects, drips, or surface irregularities can be carefully treated after curing.

Minor imperfections can be smoothed with fine sandpaper and then polished with a polishing paste. For small scratches or damaged areas, we recommend using a repair kit.

Deep damage should be repaired as soon as possible to prevent water from penetrating beneath the coating.

Use mild bathroom cleaners without harsh abrasives. Cleaners based on mild acids are generally suitable.

Avoid stiff brushes, scouring pads, and strongly abrasive cleaning agents. Residues from hair dye, coloured bath additives, or cosmetic products should be removed immediately.

Proper care significantly extends the lifespan of the coating.

EKOPEL 2K is virtually odourless and contains no strong-smelling solvents. Any slight scent dissipates quickly.

The product has been tested according to DIN EN 71-3. However, we still recommend using standard protective gear such as gloves, safety goggles, and ensuring good ventilation during application.

Avoid contact with skin and eyes.

Cured material can generally be disposed of with household waste. Uncured material residues must be disposed of as hazardous waste.

Liquid leftovers can be mixed together and disposed of after they have fully cured.

Store the material in a dry place, tightly sealed, and at temperatures between +5 and +35 °C. The shelf life is 2 years from the production date.

The material has a shelf life of 2 years from the production date when stored dry, well sealed, and at temperatures between +5 and +35 °C. The product can be used within this period.

With proper surface preparation, correct application, and regular care, the new coating can last for many years.

The actual durability depends greatly on the surface preparation, application process, cleaning, and daily use.

Yes, EKOPEL 2K can be coloured with the appropriate EKOPEL colour pastes.

The colour should be added to component A before mixing with component B. The required amount depends on the specific colour chart.

Alternatively, pre-coloured versions can be used if available.